Exactly How to Install a Bath Tub in Your Bathroom
Exactly How to Install a Bath Tub in Your Bathroom
Blog Article
This post listed below involving How to Install a Bathtub is amazingly entertaining. Give it a go and draw your own ideas.
Installing a tub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is easily obtainable, the project can move rapidly; if you have to open up a wall surface to get rid of the old tub and position the brand-new bath tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and set in the brand-new one. See to it you have certified on your own for the task and are comfortable trying it. As opposed to employing a contractor to take over a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Opportunities are you might require a specialist plumber to make tube connections.
This article will certainly assist you install a new bath tub in your bathroom if you have actually currently purchased a new bathtub as well as don't require to alter the arrangement of your previous water system pipes.
Your tools as well as material list ought to comprise the following:
Getting ready for the Installation
To start with, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the faucets device to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the supply of water. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be rather bothersome due to the limited access that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the remaining water that will originate from the pipelines. When the supply pipes have been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning during this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Prior to going on to fit the new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of both wood boards under its feet, place the bathtub in the required position. The wooden boards are valuable in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the level as well as changing the feet on the tub till the level reviews degree.
To set up faucets, fit the bottom of the furthest versatile tap connector to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
Turn on the water system as well as inspect all joints and new pipework for leaks as well as tighten them if needed. Fill the bath tub as well as additionally inspect the overflow outlet and the normal outlet for leakages.
Ultimately, take care of the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub ought to wait until the bath tub has actually been utilized a minimum of once as this will resolve it into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a link to the current supply pipes.
If you require to fit a monobloc, then you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin making sure that the washers remain in location in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The previous type ought to be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to split an inflexible seal, creating the water to penetrate the wall in between the bathroom and the tiling, causing complications with moisture and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and fittings. They are sold in tubes as well as cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to permit the movement experienced when the tub remains in usage. The sealer can crack fairly early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily offered on the marketplace. It is suggested to fit the floor tiles making use of waterproof or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on Tools You Need to Install a New Bathtub ? Place feedback down below. We'd be delighted to listen to your opinions about this entry. We hope to see you back again in the future. Please set aside a second to share this blog if you liked it. We thank you for reading our article about Installing A Bathtub.
Go Services Report this page